Shop VAL 6 heater parts

Parts for VAL 6 radiant heaters. If you dont see the part you need, let us know, we can order for you.

The KSL-B-25B burner control is the brain of the heater.
Burner Cover DS-B-26A VAL6 Daystar heaterCircuit Board KSL-B-25B burner control KBE5LCircuit Board KSL-B-25C Burner control KBE5S only 2006-2007

$75.00

$200.00

$200.00

Replacement 110 volt, 8 inch power cable. In the first 10 seconds of ignition, the electrodes spark and ignite the fuel. This set of electrodes is the same part throughout all part numbers referenced above. It fits Daystar models produced from approximately 2006 onward. The filters shown are the two filters for the VAL 6 heaters. The smaller filter is the DS-T-06 filter for the DAYSTAR models
Cord VAL 6 KSL-B-19B 8" power cordElectrode KSL-B-07A VAL 6 also part# DS-B-07A NA-R-13Filter Element DS-T-06 Daystar by Val6, MPX, Z-1

$25.00

$30.00

$16.00

Filter Element VAL 6 KSL-B-14 The flame monitor is a safety feature that reads the flame and shuts down the heater if the flame it "sees" is not ideal. Fuel cap for VAL 6 heaters
Filter Element VAL 6 KSL-B-14Flame Monitor VAL 6 KSL-B-11A also part# DS-B-16Fuel Cap VAL 6 KSL-T-18

$14.00

$40.00

$12.00

Fuel Filter Complete KSL-B-13 Val 6 Heater This is the filter that is in the tank where you fill it with kerosene The fuel gauge will let you see how much fuel you have left in the tank. Another important feature of the gauge is the small air hole in the center of the clear disk providing an air vent for the tank. This gauge has a 6" stem
Fuel Filter Complete KSL-B-13 Val 6 HeaterFuel Filter DS-T-03 Val 6 DaystarFuel Gauge VAL 6 KSL-T-17 with 6" stem

$55.00

$12.00

$25.00

Fuel Gauge VAL 6 KSL-T-17V with 11" stem Fuse VAL 6 KSL-B-17A This part# DS-B-05 .30 x 80H nozzle is for the VAL 6 Daystar N
Fuel Gauge VAL 6 KSL-T-17V with 11" stemFuse VAL 6 KSL-B-17A Nozzle DS-B-05 VAL 6 Daystar N .30 x 80H

$25.00

$4.00

$10.00

The DS-B-05A Nozzle is for a VAL 6 Daystar N-02 .40 x 80H Nozzle KSL-B-04 for Val 6 .85 nozzle Nozzle KSL-B-04A for KBE5L Val 6 .75 nozzle for hi/low
Nozzle DS-B-05A VAL 6 Daystar N-02 .40 x 80HNozzle KSL-B-04 for Val 6 .85 nozzle Nozzle KSL-B-04A for KBE5L Val 6 .75 nozzle for hi/low

$12.00

$10.00

$10.00

The on/off switch assembly attached to the control board and face plate. This pump KSL-B-12B is for the VAL 6 heater KBE5S, KBE5L
On Off Switch VAL 6 KSL-B-29Pump DS-B-24B Daystar HeaterPump KSL-B-12B VAL 6 heater KBE5S & KBE5L

$24.00

$300.00

$260.00

The KSL-B-38A Val 6 repair kit includes two filters, two o-rings, one fuse, one nozzle, and one nozzle wrench. The KSL-B-38C VAL 6 repair kit includes two filters, two o-rings, one fuse, one nozzle, and one nozzle wrench. Replacement, quick-connect wires to attach an external thermostat.
Repair Kit KSL-B-38A Val 6 with .85 nozzleRepair Kit KSL-B-38C Val 6 . with .75 nozzleT-stat Cable VAL 6 KSL-B-43

$41.00

$46.00

$9.00

The KSL-B-27 is a transformer used on a few models of VAL 6 heaters KSL-B-27 (KBE5S & KBE5L) EPX-2-30 (EPX) The ignition transformer applies direct spark for ignition.
Transformer VAL 6 KSL-B-27 also part# EPX-2-30

$100.00

Parts for VAL 6 radiant heaters.

If you dont see the part you need, let us know, we can order for you.